Wolf · Phoenix
Range Repair
Dual-fuel and all-gas Wolf ranges: ignition and burner faults, simmer that will not hold, griddle heat and dead oven cavities.
$89 service call — the visit and the diagnosis, credited against the repair. Visits 8:00 am – 8:00 pm, seven days.
In your words
What people describe when they call about this
If one of these is close, say so on the phone — it usually narrows the likely part before anyone leaves the yard.
- “A burner sparks away for a minute and never catches”
- “No usable simmer — the low setting either roars or drops out”
- “Burners still work but the oven side died after a storm outage”
- “The griddle scorches at one end and barely warms at the other”
What it comes to
What these repairs run, in ranges
Flat $89 service call covering the visit and full diagnosis, credited against the repair once you approve it.
The repair itself is quoted and agreed with you before a tool comes out — what failed, what putting it right takes, and what that totals. Approve it and the $89 comes off that total; decide against it and the service call is all you owe. The ranges below are parts and labour together, and which end of a band a job lands on comes down to the part and how much has to come apart to reach it.
- Igniter or spark module $170–$450
- Burner valve or orifice service $240–$600
- Oven thermostat or sensor calibration $200–$420
- Convection fan or motor $280–$700
- Control board or touch panel $470–$890
- Door hinge, glass or seal $280–$750
Worth the comparison: a comparable professional range, before installation and ventilation work runs $8,360–$18,800. That is the reason nearly everything on this list is worth putting right rather than replacing.
What the visit actually is
Four readings, then a part
Most of what people are told is a dead control board turns out to be a pressure, a resistance or a blocked port. So the call starts with instruments, in this order, and the number decides what comes off the van.
-
Gas side
Manometer on the manifold tap to read pressure in inches of water column, then again with every burner lit. A simmer that will not hold is far more often supply or a bypass setting than a dead valve.
-
Ignition
Spark gap and electrode condition, module output, thermocouple millivolts at the flame. Clicking that carries on after the flame is up is a switch or a grounded electrode, not the whole module.
-
Oven cavity
Probe on the centre rack through three full cycles against the setpoint, plus the sensor resistance cold. Drift and a hard sensor failure look identical on the panel and want different parts.
-
Air and heat
Convection blower current and rotation, door seal along the whole gasket, hinge tension, and for ventilation the blower draw plus static in the duct at the roof cap.
Work is carried out 8:00 am – 8:00 pm, seven days, and the $89 service call is credited against whatever the repair comes to.
Reviews
What people said afterwards
Wolf cooking calls in Arcadia, Biltmore, North Central Phoenix and Ahwatukee.
4.9/ 51,885 reviews
Clicking carried on long after the flame was up, all evening if you let it. A knob switch had stuck closed from an old boil-over. Silent since, and he vacuumed the dust out while he was under there.
Trey M.Ahwatukee
Simmer was impossible — the low setting either roared or blew itself out. He read the manifold pressure, reset the bypass screws, and now a pan of citrus marmalade sits at a bare bubble.
Nolberto B.Arcadia
Oven side quit after a monsoon power flicker while the burners kept working. Blown thermal fuse plus a tired relay. He tested both in front of me and the range baked that same night.
Roselyn K.Biltmore
The work
Other work we take on this equipment
-
Oven Repair Wolf built-in wall ovens, steam ovens and warming drawers — temperature drift, convection failures, door latches and panels that lock out. “It preheats for an hour and still sits well under the set temperature”“The convection fan grinds, then stops part way through a bake” -
Cooktop Repair Wolf gas, induction and electric cooktops and rangetops: spark electrodes, sealed burners, elements and glass touch controls. “An induction zone shuts itself off a few minutes into a big pot”“The flame is yellow and leaves soot on the bottom of the pan” -
Range Hood Repair Wolf ventilation hoods, liners and inserts — blower motors, speed switches, baffles, lighting and the ductwork above them. “Grease and smoke drift into the next room instead of going up”“Only half the lamps come on, and those flicker”
Describe the fault. We will tell you what it usually is.
range repair in Phoenix, AZ. Call and describe the symptom, or take a slot on the booking page — there is no form to fill in on this site.